China portable auto horizontal fillet welding carriage for speed welding and plasma cutting, Find details about China welding tractor, welding carriage from portable auto horizontal fillet welding carriage for speed welding and plasma cutting - Wenzhou Zhengte Electric Welding Equipment Factory
Horizontal speed: 0–120 cm/min (0–47.2 in/min) Vertical speed: 0–110 cm/min (0–43.3 in/min) Weight: 20 kg (44 lbs) Welding settings storage: 1 (last used) Oscillation type: linear (0 - 100 mm) Oscillation (weaving) pattern: trapezoid, triangle, straight line: Oscillation width: 0–50 mm (0–1.9”) Oscillation speed: 0–1500 mm/min (0–59 in/min)
The settings for Flux-Core wire and non-ferrous metals will be completely different. Metal Thickness & Amperage Settings: When welding mild steel, a good rule of thumb is to set the amperage level at 1 amp for every 0.001” of thickness. So if you are welding 12 gauge mild steel with a thickness of 0.100”, you would set the machine at 100 amps.
Use the chart below to set the wire speed based on the wire size. For example, if the wire size is 0.23 inches (used for sheet metal), then you need to multiply by 3.5 inches per amp, which is equal to 437.5 ipm. .023 inch Multiply by 3.5 inches per amp. .030 inch Multiply by 2 inches per amp.
Proximity sensor (5mm) provides automatic stop function at 5mm from end of steel plate. 3. Constant speed and showing exact speed on FND by T.G control. 4. The cariage can avoid obstacle stiffeners. 5. Above 10mm width of bottom plate applicable. 6. Fillet welding carriage for Stitch/Continuous.
Ideal choice for butt weld, fillet weld, double V joint welding of plates as required in ship building industry, railway, construction of bridges, components of earth moving equipments etc. Most suitable for thick plate welding applications where X ray quality welding with excellent mechanical properties and good finish of weld beads are ...
Wire speed Reference Steel Thickness (mm) Wire Speed (metres per minute) Wire Speed (metres per minute) 0.6mm wire 0.8mm wire 0.8 2.5 1.6 1.0 3 1.9 1.2 3.6 2.2 5 more rows ...
I MIG 600. Features: Using IGBT modules and advanced welding current waveform control technology. Low spatter and higher performance welding. Crater "on / off function, crater voltage and current are adjustable. Protection function : Single Phasing, over heating, over current, under voltage. High efficiency of machine's output.
On a fillet weld weld this keeps the contact tube to work distance set without the need for a torch height control. Automatic Shut Down at the end of the weld Limit switches at each end of the carriage allow the operator to set up a pre-determined stop point using a magnetic block. Once the limit is tripped, the machine travel and welding Stops.
The following tricks and tips are what separate professional first class MIG welders from the rest: When it comes to MIG welding a properly set up machine is the most important part. MIG welding is easy but machine set-up it critical and requires a strong knowledge of the proper settings.
The Rail Tug is a track carriage designed to cut and to make butt and fillet welds. The carriage allows MIG/MAG, SAW, oxy-fuel, or plasma torches. The track is clamped with magnetic units to ferromagnetic surfaces that are flat or curved. Accessories allow, examplefor , using torches with a larger diameter, and guiding
MAKO- Z Simple automatic welding carriage for Vertical,Horizontal and Flat Welding with function of interlocking with MIG and CO2 Welding Machine.
• Closed loop speed control system • 0-1200mm/min horizontal speed • Heavy duty European made portable fillet welding carriage designed to produce consistent high-quality welds • 4 -wheel drive with magnetic base allows for vertical & horizontal welding • Constant, continuous and repeatable travel speed with closed loop speed stabilisation system • Multifunctional LED display
I would say around 18 volts and a 260 wire speed would be a good start. and as John said, run your focus mainly on the heavier plate, and let the puddle wash in rhythm onto the 1/4 plate. Dont use too much angle and also, watch the wetting. clean the surface really well, the mill scale can contribute to under cut.
Speed controls maintain an even weld bead and penetration; this reduces over-welding and, in turn, reduces costs. Distortion is controlled by maintaining a constant heat affected zone. Wire and gas waste is reduced as only the determined amounts of these are applied to the weld bead. Weld carriages can be used for MIG, TIG, and SAW welding.
China portable horizontal fillet welding carriage ZT-5A digital display with travel speed 990mm/min, Find details about China fillet welding trolley, fillet welding carriage from portable horizontal fillet welding carriage ZT-5A digital display with travel speed 990mm/min - Wenzhou Zhengte Electric Welding Equipment Factory